TPR2 Non - Flammable Paints:
TPR2 paints can be sprayed with standard air/airless equipment. The specifics below provide the critical characteristics for choosing the right equipment. TPR2 offers pre-assembled, ready to use sprayer setups at www.paintproject.com
Please remember some important items relative to your application:
Any ceiling application (we assume there will be horizontal and vertical
surfaces in your job) goes on at 1/2 the stated max/coat thicknesses to
prevent dripping. So, where 1 application coat might suffice on walls (to
achieve the required .018" dft) without sag, The contractor will need to
spray 2 thinner coats on a ceiling. This is conventional knowledge for
spray people. In general, we recommend a 'tack' coat application of the the
coatings first, then a full coat will achieve the stated dry film thickness
of .018".
TPR2 defines its coating coverage's on 3rd party tests as Wet Film
Thickness(WFT) and Dry Film Thickness(DFT). This is done so that the
coating application will be accurate independently of the substrate and also
easier to confirm compliancy with 3rd party test results. Remember, Porous
surfaces(fresh sheetrock, plywood, etc) will absorb more coating and thus
take more product to meet thickness requirements than recoated or non porous
substrates(metal, plastic, pre coated wood/sheetrock). TPR uses the attached
procedure to measure wet film and dry film thickness....GET COATING MEASUREMENT PROCEDURE
See how easy FIRESHELL® sprays: On Wallboard
See how easy FIRESHELL® sprays: On Foam
AIR SPRAYING
IP series, FR series, ME series (Paints)
SCHT1 series, HS series (Coatings)
AFES series (Flexible High Build Elastomerics)
We recommend the following systems:
Binks 2001 gun or equivalent with a 68SS-68PB air cap ass'y and a 2 qt pressure cup.
HVLP Gun (.070²) fluid nozzle with 2Qt. pressure cup with 1.5 HP
compressor & 6 CFM total air.
TPR2 offers pre-assembled, ready to use sprayer setups at www.paintproject.com (Mention "TPR2 Airless" or "TPR2 Air" when ordering)
AIRLESS SPRAYING FIRESHELL®and TEMPROTEX® Series Thermal Coatings
MODEL
SPEC.
TIP
Graco GMAX Texspray 7900HD
2.2gpm/3300psi
525 to 531*
Graco 1095/ASM3100
1.15gpm/3300psi
525 to 531*
SprayTech EPX2455
.85gpm/3100psi
525 to 531*
Titan 740IX
.72gpm/3100psi
525 to 531*
Glidden Speeflo Power Twin
1gpm/3000 psi
.031" tip*
Glidden Speeflo Power Twin
1.25gpm/3000 psi
.031" tip*
*Graco LTX525 to LTX531 tip recommended (blue nozzles)
AFES Mastic (120+ku)
TYPE
EQUIPMENT
RATE
PRESSURE
TIP SIZE
Max WFT/coat
Pnuematic
Graco King 45:1
3gpm min
4000 psi
51-55tip
30 mils or more
Gas/Hydrolic
Graco GH833 40:1
3gpm min
4000 psi
51-55tip
30 mils or more
IP series, FR series, ME series (Paints)
EQUIPMENT
HOSE SIZE
PRESSURE
TIP SIZE
Max WFT/coat
.6 gpm Airless
1/4" X 25'
3000 psi
0.021
22 Mils
SCHT1 series, HS series (Coatings) * For Non-Porous, Vertical Surfaces. Porous and/ or
Ceilings will be less.
